Recent content by jbrotschul

We have catalyst 6009's as our access switches. Looks like there is a legacy configuration (project) to enable MST, but was never activated. Is there a way for me to quickly (and safely) remove this code? -------------------------------------------------------- Every port on every blade has...

Can anyone recommend a cordless phone with noise-cancelling that would work well to connect to a POTS line in our data center? Please let me know. Thanks

ip route 192.168.151.0 255.255.255.0 192.168.4.7" would route all traffic destined to 192.168.151.0/24 to 192.168.4.7... I need to route all traffic from source ip range 192.168.151.0/24 without a destination specified in the routing table to 192.168.4.7 rather than 192.168.100.7.

Hi, I have a Cisco Catalyst 4506. Currently there is a default route configured pointing to my firewall for internet traffic... ip route 0.0.0.0 0.0.0.0 192.168.100.7 I installed a new firewall - 192.168.4.7, and want to route traffic based on the source ip to this new firewall for only...

Hi, I have a Cisco Catalyst 4506. Currently there is a default route configured pointing to my firewall for internet traffic... ip route 0.0.0.0 0.0.0.0 192.168.100.7 I installed a new firewall - 192.168.4.7, and want to route traffic based on the source ip to this new firewall for only...

config below... i substituted our ranges with this list... Internet IP range 199.99.199.0/24 DMZ IP range 192.168.6.0/24 Internal IP range 192.168.XXX.0/24 PIXFIREWALL# wr t : Saved : PIX Version 7.2(2) ! names dns-guard ! interface Ethernet0 speed 100 duplex full nameif outside...

Hello, I am running a PIX515E with version 7.2(2). We have discovered an issue with the DMZ network. The problem is when dmzserver1 tries to communicate with dmzserver2, dmzserver1 is receiving arp replys from both dmzserver2 and the DMZ interface on the PIX. So depending on which reply is...

Okay. I check my protocol inspection, and smtp/esmtp is not there, so I believe I have it configured properly. But my admins are stating that some smtp connections from our back-end pmdf email system are getting hung trying to connect to the exchange server. The pmdf email servers are on the...

I recently upgraded a PIX515E from 6.3 to 7.2... On the 6.3 os there was a line "no fixup protocol smtp 25" that doesn't appear to translate over to 7.2... I'm going to read up on it, but was hoping someone knew how to translate this command to 7.2 (or if it is even needed anymore). I...

Does anyone know the exact TCP Port #'s used when an outlook client communicates with an exchange server? I would like to set up some traffic shaping in our remote offices to protect this traffic. Feedback much appreciated.

We are using Cisco VPN Client 5.0 terminating on Cisco PIX515E firewalls. When connected via the vpn client, we can't access resourses on the other end of a seperate Point to Point VPN terminating on a router dedicated for customer vpn connections. The access list for the Point to Point VPN...

i found the problem... due dilligence was not done on my part... Note: For the HWIC-1FE and HWIC-2FE the minimum level is Cisco IOS 12.4(15)T. http://www.cisco.com/en/US/prod/collateral/routers/ps5854/product_data_sheet0900aecd80581fe6_ps5855_Products_Data_Sheet.html

I tried a few different hwic slots... I guess it could be a bad card. Here's the sho ver: Router#sho ver Cisco IOS Software, 3800 Software (C3825-ADVIPSERVICESK9-M), Version 12.4(5b), R ELEASE SOFTWARE (fc2) ROM: System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1) Router uptime is...

I need to add an ethernet interface to a cisco 3825 series router. I powered off the router and installed a hwic-1fe module in an open slot. But I don't see the interface after I booted the router. Should the router automatically see new module, or is there a command set needed? Please let...

[COLOR=blue]I have a traffic shaping example that I hope someone can explain to me... Particularly the difference between the police and police cir lines...[/color blue] class-map match-all Officename match access-group name Officename_access class-map match-all Pop_Restrictions match...