Recent content by motoslide

I'm not 100% on this, but I thought it was pretty typical that a secondary partition on a RAID drive would be accessed as the same SCSI ID, but with a LUN of 1. However, it appears that you must have the correct settings if it was able to locate a filesystem. "Proof that there is intelligent...

Same here. Still got some 3.2 SCO Xenix media on 5.25" floppies. I think it all fit on 2 diskettes! I've been a long-time hold-out hoping for a bright future with SCO, but I gave in a couple of years back and have mostly switched to CentOS. But, running 5.0.7 or 6.0.0 on ESXi seems pretty solid...

That's precisely the reason many folks are opting for VM technology. You can run ESXi on that new hardware, then install SCO 5.0.7 as a Virtual Server. There are other flavors of VM as well, of course. Even if you got the HD to work on that motherboard, you might run into problems with the...

I wouldn't suspect so, but can your SATA controller be configured for IDE emulation? "Proof that there is intelligent life in Oregon. Well, Life anyway.

Are you able to send email from that same IP using Outlook or some other device? The message in your post would indicate that the IP address has been flagged by Spamhaus. If so, I don't think you can resolve this by reconfiguring MMDF. If that's not the case, and you only need outbound email, I...

The drive is likely compatible (for reading a CD), but the controller it's attached to would be a more critical issue for compatibility. "Proof that there is intelligent life in Oregon. Well, Life anyway.

If you can't locate compatible hardware, you should be able to load this on a VMware box. I was bored today (and haven't played with 5.0.5 and btld stuff for years) so I followed this link with good success: http://groups.google.com/group/comp.unix.sco.misc/msg/9bad2852a40218aa I had a 5.0.7...

I've got a driver disk with this information on the label: Unix V.3 Driver SCO Unix / Xenix, ISC Unix Version 7.01 Copyright 1993 Specilix International Specialix devices had some hardware changes during that time frame, so it's possible my drivers wouldn't be compatible with your hardware...

There's not much to go on in your question. The first thing which comes to mind is that the SCO box which doesn't work over the VPN has an incorrect default GW, or netmask. "Proof that there is intelligent life in Oregon. Well, Life anyway.

Check the perms and ownership in the /usr/spool/lp/admins/lp/printers area. If you have bad permissions, some of those commands will stop before displaying all the records. That's where I'd start at least. You can also run the /tcb/bin/integrity -e command and see if it complains about lp...

It would probably be best to start this issue in a new thread, as your question has nothing to do with this thread's subject. This is probably an application-dependent issue. Are you talking about text files or ??? You can allow the Windows server to map a shared resource on the SCO box. That...

SCO doesn't have a "5.1" release that I'm aware of, but that's probably not important. The 1/42 designation would indicate a full disk on the root (main) filesystem. As VodkaDrinker stated, this can be caused by a log file which has consumed a great deal of space. It can also be caused by any...

It's always nice to have a second "root" account just for such issues (or especially when root's password is accidentally changed and doesn't get noticed for weeks or months). Just create another user account, then change the UID to "0" in /etc/passwd and /tcb/files/auth/{a-z}/{newuser}. In the...

You've got PCL codes in the data, so this isn't truly just "text". My best guess is that the data is sending <CR> (^M) without <LF>. Which is pretty odd. In most cases, it's the opposite problem (<LF> without <CR>). You can determine that for sure by printing the hex-dump of that file. If you...

Have you looked closely at the output before it hits the printer? Disable the printer, send a job from your application, then look for the file here: /usr/spool/lp/temp The file to review is the one with the "-1" extension. I would do a hex-dump of the file. Your application might be sending...