Recent content by Salvalinus

Anyone got any positive or negative feedback on using either TACACS+ or RADIUS for access/authorization/accounting for telnet/ssh access to manage Cisco equipment?<br><br>Specifically, I'm looking for comparisons and/or real-world experiences that might sway my decision to use one protocol over...

What does the routing table on the server 192.168.1.10 look like?&nbsp;&nbsp;Does it know how to get to the network 192.168.3.0/24?&nbsp;&nbsp;If I understand your description correctly, I'll bet it doesn't.&nbsp;&nbsp;I doubt this is your internet problem. <br><br>You don't give any indication...

Ah, 6513??? Are you sure this product exists? I don't think Cisco makes a Catalyst 6513.<br>

How long is that fiber segment? I believe the max distance for 100baseFX Half-duplex to a repeater/HUB is only something like 160m. I have had trouble with long fiber distances even switch to switch that were auto-negotiated to half-duplex. Since you are using a hub on one side you will, of...

I assume you are talking about a 2B+D BRI ISDN line.<br> <br> You should be able to use one of the 64k B channels for voice at the same time you are using the other one for data. There will be no slowdown in the 64k data channel per se, but you might be using both 64k channels for data normally...

I assume we are talking about RJ48C for the T1 and RJ48S for the 56/64k DDS right?<br> <br> I can't remember specific colors but the pins should be<br> <br> DDS 56/64k on RJ48S<br> -------------------<br> T -- 7<br> R -- 8<br> T1 -- 2<br> R1 -- 1<br> <br> T1 on RJ48C (oh I guess a RJ48X is...

When you say &quot;significant&quot; what do you mean? What percentage (collisions/packets out)? How much data are you sending while the collisions are occurring? Is it possible that you are overloading the 100Mbps half duplex connection? Is this just a single HUB with no other connections...

If you have console access and know the enable password all you have to do is login, enable, and do a `write erase`. The 2900 uses (for the most part) standard IOS. This will erase ALL of the current configuration, so make sure this is what you want to do before you do it.

Sorry, I know this is like a month late, but just in case you haven't<br> gotten it working yet here is some config stuff that should work.<br> <br> All of the usual disclaimers apply. You may or may not problems with this<br> configuration. I welcome anyone to correct me where I may have...

Sorry, for not replying back when I said I would. Things have been very busy.<br> <br> I'm sure you got this figured out by now, but just in case you haven't.<br> <br> Just by quickly looking this over I would say things should be working accept that you probably need to add<br> <br> int ser...

No, DLCIs are assigned by the telco. You will have one (per side) for each PVC (permanent virtual circuit). The DLCI is essentially the layer two address used by the local router to tell the frame relay switch which PVC a particular data stream is supposed to travel on. It has nothing at all...

I thought I'd ask if you got this working before I went to the trouble of entering what will probably turn out to be a long answer.<br>

I'll assume that we are talking about having a WIC-T1 card installed since the 1604 doesn't have an S0 interface with out a WIC-T1 and any other WIC card wouldn't be capable of doing async dialing.<br> <br> Make sure you have the following configured on your router:<br> <br> interface serial...

I assume you are looking for something inexpensive and probably for an MS-Windows based PC. WhatsUp Gold by Ipswitch isn't too bad, and is relatively inexpensive (about $695 I think). You can find information at<br> <br> <A HREF="http://www.ipswitch.com/Products/WhatsUp/index.asp"...

Yes, what you describe is possible provided your router can act as a DCE and provide clocking to your &quot;circuit&quot;. You'll need either a cable specially made as a cross-over or you can also buy a standard male v.35 DTE cable (used for connecting a router to a CSU/DSU) and a female v.35...