Search results for query: *

Hi all, I have a BCM400 4.0 system which is acting strangely i.e. all the LEDS except the Power and HDD are blinking green. Power LED is solid green and HDD is just showing kind of normal activity meaning it's not constantly blinking nor it's turned off. From what I've read I suspect that the...

Hi guys, I have a BCM400 system in-house and I'm facing some challenges to configure outbound call routing rules but because of my limited knowledge about BCM it would be great if you could point me how to fulfill this task. At the moment I have one active ISDN PRI trunk with local telco...

Hi All, Does anybody knows if we could use "Pause" option when using "Digit Conversion Table"? I have a situation where the customer is using some low-cost VoIP provider that got local number we need to dial and then it provides a dial tone from their system. In example, I'm configuring one...

Hello, I was changing the DN name on Meridian OPT 11C and everything works fine, but after a power failure the name is back to the old name before the change. After a investigation I've noticed that in ld 43 the database is old. Here is the Output: ---------------- .dat DATABASE ISSUE...

Hi guys, I have one older ipLDK300 system which I'm due to install, but the request is little unusual because of the distances between the PBX (SLIB2E boards) and the actual analog phones. It require the phones to be separated from the PBX around 1.500 meters (1.5km). The specification says if...

Hi guys, I'm thinking over a scenario of iPECS-MG100 with 20 agents using DKT's along with EzPhone clients. I dont'have much experience with EzPhone applications but I'm sure that with ipLDK 100/300/600 when using ezPhone with DKT 7000 series you needed a CTU module mounted on DKT 7000's in...

Hi all, I have a BCM400 single cabinet which has few DSM32+ and one ISDN PRI module. It user 2/6 split and the capacity in means of available slots is filled. I'm in process of upgrading the system with an additional cabinet and another PRI module which will be hosted on the second cabinet...

Hi all, I have a repeating problem with one ipLDK100 with BRIBE card and 4 ISDNs BRI connected to it. The problem is that almost on every outgoing call the first attempt is unsuccessful wiht and error message showing on the DKTU's (ISDN Line Released). The second attempt is successful and I...

Hello, I've got a very strange problem with a ipLDK 20 setup. I got ipLDK20 with ext 100 as System Attendant and the phone is LDP7016. I've set the PSTN with DISA to play VMIB message 1 and i got additional lines also playing VMIB message 1 but for the ISDN lines i'm using the Flex table. On...

Hi all, I'm little bit confused with the Weekly Time Date settings table as I previously thought it is the only point of setup to set different ring rules for different time of the day/week. My point is using a Ring Assignment tool and Weekly time table to set day calls during the working...

Hello, I have BCM 400 with 8 ISDN BRI lines(16 total) and currently i an using the CallPilot CCR for the lines with company greeting and CCR tree. Now i want to use some DID numbers to go to specific DN without the CCR and to have the CCR for my main number. As i can see in the CallPilot i...

Hello all, As this is the first time I'm setting up the Door Phone interface with Aria Soho systems, I'm experiencing problems i.e. I'm stuck with the connection issue. I have correctly setup the AR-DPU2 (door phone internal interface module) and connected the LDP-DPB module as instructed...

Hello all, I'm thinking to connect 6 distant offices, each one with its own ipLDK20 system (as there will be 6-7 people on each location and they will need local telco service too) through IP Networking. All locations will be in the same virtual network (VPN), so I wander if anyone has this...

Hi all, I need to install an ipLDK20 with 11 IP telephones. I have never dealt with an IP phones on the ipLDK20 so I wander if I will be able to register all 11 phones with 4 port L20 VOIM module? I know that it's shared voice channels but just an aknowledgement will be ok. Anyone done this...

I have setup an Auto Attendant (recorded company greeting) which is followed by CCR Tree prompts. Everything works fine, but the thing that is bothering me is the loop. I don't want all of the sequence to loop, but instead I need AA (customer greeting) then CCR Tree prompts and after it finish...

Hi all, I have a little strange issue with an Aria SOHO caller ID setting. We use FSK here and as we all know Aria SOHO systems has integrated CID option. We set it up correctly and it works on any analog and digital extension (Caller ID shows up correctly) except on the master digital LDP7224D...

Hi all, We have started iPECS testing and was attracted by SIP over TCP function in PGM 133 with the newest software release: E.0Dr. Our main goes was to integrate iPECS with Microsoft OCS2007 in which we partly succeeded. As you probably know OCS use SIP over TCP which is not case with many...

Hi all, I usually work with ipLDK and now with an iPECS system, but I have a request for an Aria SOHO with a hotel software. Is there hospitality software for Aria SOHO systems? It seems I could not find any. Best Regards, Ivo

Hi Guys, I've been trying the whole day to install ezPhone delux TAPI phone on my PC but beside it gone to my nerves I haven't been able to run it successfully. "LINE OPEN ERROR" over and over again. Let me tell you what have I used. I've tried with an ipLDK20 system. I have Demo Keys On so I...

Hi all, I have ipLDK300 installed at a customer site with 4 ISDN BRI and 15 DID's. I do not have any auto attendant settings ie. every extension got it own DID. The problem is the following: I use "DID conversion conf type 0" i.e. the number 3091557 leads to extension 157. "DID Disa...