Search results for query: *

will a door opening controller work with analog phones? it seems that the cordless phones are having a problem with dialing the 6 to release the door. I am going back out in the am to check the dip switches on the DOC but it should have been default (6) the release from the soft button on the...

I have a customer that has 5 telephone numbers that dial out get a ringback then drop the call the Carrier says that the MICS is dropping the call but I cannot see anything that would be causing it occasionaly the call will connect and work fine other telephone numbers work fine the intercom...

I have a MITEL 3300 ICP We want to have the Reception desk (1101) be able to call forward incoming trunk calls, I have set up a ring group with the ext 1101 and the file room 1177 to both ring on incoming calls. I can get the phone to forward internal calls to a new hunt group (2201) but the...

I am looking for an interface with a talkback amp/telephone interface that incorporates a desk/boom mic and Push to talk. any ideas/suggestions on what I can replace the telephone set that the customer has with? the customer wants a boom mic/speaker setup to work with the talkback amp...

I have a customer that has a mitel 3300 and they asked me to get them caller id. (Church, got it donated, keep it cheep etc.) and I thought I had the programming correct but am not seeing caller id on incoming calls. I looked at the analog card that the trunks are coming in on and it is a...

I have a customer that wants to limit call time on analog lines. anybody remember seeing a device that could drop calls after a preset time? 15 to 30 min. ---------------------------- 40: Hill?? What hill?? I didn't see any $%@#(*$ Hill!! 50: who put this $%@#(*$ Hill Here...

I have a customer that has a comdial DX-80 system, problem he has is that for some reason there are calls coming in to them on their 800 line after hours that are not disconnecting so customer gets anywhere from 100 to 700 minutes of calls each night. the customer wants to force disconnect...

Got a Mitel 3300 that was donated to the local church. The system still has its original programming (it was a call center with a couple of T-1's) and I need to drop it down to 2 CO trunks. I did go to the analog trunk form and have cab 2 shelf 1 slot 3 circuit 1 type 4 port LS already in...

I went to a customer on a BCM50 W/voicemail a few weeks ago. I reprogrammed the CCR Tree paths. cust just called back and says the voicemail CCR program went back to the way it was before I reprogrammed it. I did the programming from the telephone set. is there anything that causes...

Got called out to a customer site. They have a Comdial DXP Plus (Hotel) and wanted to add another station. the wiring was dead simple but the cust had added the ext number on the system but the phone isn't forwarding to voicemail for them. How do I create a voicemail box for the new extension...

I have an RV042 router that had 5 IP's from charter x.x.x.234 thru .238 we have .234 as the main IP for the site and it is port forwarding multiple ports correctly to a server on the LAN 192.168.2.251. problem is that while we set the firewall up to pass all ports for .236 (from WAN1) to...

I have a customer with a CICS that we recently bumped up to 3 digit system vs 2 digit (needed the hunt groups) a few days after that all of the message lights turned on on the phones (no message just the indicator) checking feat # 6 5 showed that there was no message waiting but the lamp was...

got a customer found an old 8 port card, stations only as far as I can tell (no services). is this beast compatable with CICS 4.1 software? Nortel NTBB04GC-93 CICS 8 Port Card ---------------------------- Hill?? What hill?? I didn't see any $%@#(*$ Hill!! ----------------------------...

I have a customer with a MICS 4.1, PRI, 1`2X0, 2 - 0X16 1 - ASM, and a NAM with Prelude. problem is that for some reason the Route tables disappear, main problem is that table 009 disappears which corresponds to Destination code 9* the PRI call out routine. as you can tell I wasn't looking...

Can the BCM support non-Nortel phones? specifically I was wondering if a Wireless access Point could be attached to a BCM network and run wireless phones such as the Linksys WIP300 or their CIT200? ---------------------------- Hill?? What hill?? I didn't see any $%@#(*$ Hill...

I am trying to convert a list of polar coordinates (in degrees not pi) and distance from center to XY coordinates. Problem is that x=r COS(angle) and y = r sine(angle) while returntin to me values the positive and negative values are a bit hosed R Angle X Y...

I have a customer that is in a metal building and so the signal from the base station dosen't pass outside very well. since they have a show yard to move around in I am hoping that someone has an idea on how to remote an antenna out of the building. ---------------------------- Hill?? What...

I am writing code in VB6 to use MSCOMM to control a modem dialing out. (no data will be passed this is just a predialer to save time on the dialing) I am not having problems yet with that code but my question is if I compile the VB6 code into an exe file will it run using the VBA that access...

We have a couple of XP machines that after a inactive period of time (few minutes to many hours) will go to the "computer locked screen" this is the same screen that we see locally if the user islogged in using remote desktop. this happens somewhat randomly, it is not a screenshot on the...

OK, our office upgraded from outlook 2000 to a newer version and of course the rules were not imported, can anybody tell me where the rules are located so I can at least get a printout of the rules and re-create them? ---------------------------- Hill?? What hill?? I didn't see any $%@#(*$...