Search results for query: *

Hello, Is there a config guide or other source someone can recommend for this. I have a lot of 3750 switches that are being refreshed with 3850 and I want to make sure the QoS settings are carried over properly. Been awhile since I worked with Cisco so my knowledge is a little rusty. Here is an...

Hello, Just wanted to see if I can get a sanity check. I have to configure the network to support LLDP-MED with Shoretel phones so it will tag and mark the voice traffic accordingly. Is this the only config I need? interface FastEthernet ALL lldp med-network-policies port 1-48 voice dscp 46...

Hello, I have a customer who is seeing this error and I have not encountered this one before. The only mention I have found for it states that a memory corruption has been detected and that it's related to dialing filters on a specific line appearance. The actual error message he sees though is...

We are having a lot of trouble with this and while I am sure it's originating from the NICs on the PC's, I need to temporary fix for blocking it on the network. The broadcasts are causing issues with teh VOIP phones and other applications. We have rate limiting enabled on the switches and on the...

Hello, We are seeing an issue all of the sudden where the ports on our ERS4850 switches are reverting back to 10mbps. This is random and not persistent. It is happening on most of our new switches and started about the same time district wide. They are all HW12,13 and 14 series switches running...

I was curious if anyone might know the answer to this. I am curious how the packet would travel in this scenario. VSP A VLAN 10 ISID 10100 VLAN 10 IP 10.10.100.1/24 VSP B VLAN 10 ISID 10100 If you were to connect a device to VLAN 10 on VSP B, and a device behind VSP B tries to communicate...

Hello, I wanted to see if anyone has done this and has any advice on it. I want to try and setup source based routing policies to route traffic out different internet connections. I'm more curious if this is possible than anything. I would like to send my data and wireless VLANS out a specific...

Hello, I am trying to setup a freshly upgraded Avaya network to use RADIUS auth for SSH/Web/console access for all of the switches and routers. They want to use their Identity engines server as the RADIUS server. Avaya says this should work, but it's not for some reason. I configured the radius...

System is a CS1000E R5.0 with Branch Office 4.5 at the campus sites. All of the phones are two locations started having issues where they could not dial any long distance or 4 digit dial other campuses. After doing some digging I noticed that these phones showed to be LOST when I did a PRT DNIP...

We have two switches that recently stopped communicating with the HQ server. The site is connect via an IPSEC tunnel. We can ping both ways, but the switches will not register. Do I need to check something else on the firewall possibly? As far as I know nothing is blocked between sites. Is there...

Hello, I am trying to setup snmp-v3 on some older 8600 chassis runnning 5.1.2.0 code. I have the encruption modules loaded, boot flag set to allow snmp and the access policy set to allow snmp-v3. I used these commands to create the snmp-v3 config. config snmp-v3 usm create Manager sha auth...

Hello, Having trouble with this. I am not sure what I am missing. Been too long I guess since I worked on these... Users on analog phones are not able to access the paging trunk by dialing the ACOD which is 7099. Here is an example of one of them. I have this problem at other campuses as well...

Has anyone set this up sucessfully. I had read over the admin guide and the instructions on this is done are vague. Mentions creating a datadump with the replication log position and then restore it on the DVS server. It also mentions modifying the my.ini file. No specific details unfortunately.

Hello. Trying to polish off a SMR install and have run into a snag. When the mobility client handover function is used, it tries to dial the handover number but drops the call. I checked the SIP logs on the SMR and was getting a 404-unkown error. Found KB article KB17243 that recommends some...

I am having a problem getting Shoretel phones to go into the voice vlan when connected to a Juniper switch. Switches are on current code and the Shoretel system is on 14.1. When the phone boots it appears to work since it pulls an IP from the voice vlan, but then it displays "Reconfiguring...

I recently migrated from a Win7 laptop to a Macbook pro. Some of my Excel files show they are locked for editing by the username on my old laptop and do not allow me to edit. Is there a way to take ownership or to remove this lock in the Mac OS? I am running OS 10.8.5.

I had to replace the system at the site where the Carehawk paging interface is terminated and can't figure out the secret combo on the trunk type. I have tried WATS, COT and now PAG. Nothing seems to work. They can dial the route access code, but nothing works after that. I have asked for some...

Hello Again, Same system..CS100 R5. Recently had to replace a TMDI and CC card on their Metro T1. Now they say it locks up and they can't get inbound calls every 3-4 days. Verizon is telling them to disable MSG maintenance on the span. Never heard of that before either. No configuration...

Hello, CS1000 R5.0. A phone using CLID table O is supposed to send out the main number for the campus. I checked the CLID table and it is setup properly. DIDN is set to NO etc. When they call me which is a LD call it shows up correctly, when they make a local call it send their extension as the...

I recently converted a branch office 4.5 system over to a MG1000E due to a total system failure of the branch office. Since I converted it the paging trunks don't work now. Not sure what I am missing. The paging trunks are accessed with IP phones, and they were working fine before, but the...