Search results for query: *

It sounds like you had alot of experiance reverse engineering your System. Do you have the wire diagram and the Batt SLA number. I may have a good source that can help you get the batteries cheap!

Hello All, I just recently purchased APC Symmetra 12KVA Power Array. The problem is I purchased it from Ebay, this system came in with out batteries. Does anyone know what type of batteries go in the APC SYMBATT Pack? PLEASE HELP!!!!! Greatly appreciated!

hahahah

Hey Andy what does Santricity say? Have you tried different disks?

Tahnk you CoderMonkey for the information you you submitted. I searched for the porgram but I didn't have much luck finding it. Can you suugest a good starting point other than Google?

Hey all I can really use some help. I have a ATL M2500 tape library that will not boot up. on the op-panel it reads BOOT CODE 3.00 and right under it it reads CRC ERROR. Can any one point in the right direction to fix this problem? Thanks have a great day!

Hey All, Does anyone know what program can I use to view the IBM LTO 3 drive via serial communication? I have a program but it limits me to IBM LTO 1 and 2's. Any suggestion?

To me this sounds like the firmware that you have installed on the drive is for an autoloader. Once you find the correct firmware for the system that you want it for and download it to the drive, it would be recognized as a standalone drive.

Hello to All, Well I just purchased a few IBM lto universal cleaning cartridges. My question is since I purchased them off Ebay, How can you tell if the tapes are new or not? There are supposed to be brand new, but they didn't come with cases. Thanks in advance guys!!!

Well I would like to say thanks for responding. I have three different PC's running through the same fibre switch, and two PC's view the ID settings as different values. This is a problem whenI try to connect to SCSI toolbox to test the drive. Because SCSI Tool Box can only see up to 127 ID...

How do I remove the over voltage LED on the Smart ups.

Hey Guys and Gals, I've been encountering issues with 9840A fibre drives. When I connect to my desk tops,4 different ones via fibre HBA. I find that two PC's will allow my STK SCSI tool box to view the drive. The other two PC's are not. What I noticed was in Device Manager the ID locations for...

Hey all, Having a great day hopefully!! Well I need to know if any one knows what is the pinout for the Seagate LTO 1 is. Let me be specific, I need the pinout from the rear of the drive and the serial pinout to 5Pin din connector that connects to a RS-422. Please all if you can help me let me...

Hello All, Does anyone have experiance in the Pioneer DRM7000 Optical jukebox? I would like to know if you have to reboot the server (which is win 2000 server) in order to see the new hardware?

Hey All I can really use some help with this. Please help me..

Hi Everyone, I have a Storagetek blade ctlr B150 and I'm trying to figure out if I can use a Storagetek blade ctrl B250 ESM interface card. Would The B250 ESM card work on the B150? Also does any know if a D178 controller will work for the B150 array's?

Hey All, I have a know good robot, but I can't get the tray to move. I tried leveling the tray with a level. I made sure that all sensors were triggered. Is ther any thing else that I should keep in mind when working on the SL500 robots?

Sorry STKman...Yes the library was on-line before the MPC swap...Thanks guys I will look at the connectors closely..

So I dropped the load to about 30% which was 2 LEDS on the left. I even bought new batteries and attempted to perform the runtime calibration. This task didn't stop the LEDS from flashing. Any other ides? I really appreciate all your help.

Thanks for the response....The FSC codes that are presented are as followed: 3381, 3329, 3311, 3109, 3383, 3313, 3312, 3007, 309e, 3106, 308f, and 3e05. When I looked up the errors most of the codes indicate a targeting issue. Which in turn leads to the hand....I know for a fact the hand is...