skipclarin
Technical User
I have set up an ISDN line from my G3R to a CTI box and it does not seem to work. Does anyone out there have any experience with this?
Here is how I have it set up.
Bit Rate: 1.544
Line Coding: b8zs
Line Compensation: 1
Framing Mode: esf
Signaling Mode: isdn-pri
Connect: network
TN-C7 Long Timers? n
Country Protocol: 1
Interworking Message: PROGress
Protocol Version: a
Interface Companding: mulaw
CRC? n
Idle Code: 11111111
DCP/Analog Bearer Capability: 3.1kHz
Slip Detection? n
Near-end CSU Type: integrated
Echo Cancellation? n
ESF DATA LINK OPTIONS
Network Management Protocol: tabs
Send ANSI-T1.403 One-Second Performance Reports? n
Far-end CSU Address: b
INTEGRATED CSU OPTIONS
Transmit LBO: 0db
Receive ALBO: 26db
Upon DTE LOS: loopback
CPE LOOPBACK JACK OPTIONS
Supply CPE Loopback Jack Power? n
The Trunk Group set up is like this:
Group Type: isdn
CDR Reports: n
Group Name: 401 CTI DEV ISDN
COR: 1
TN: 1
TAC: 234
Direction: two-way
Outgoing Display? n
Carrier Medium: PRI/BRI
Dial Access? n
Busy Threshold: 255
Night Service:
Queue Length: 0
Service Type: tie
Auth Code? n
TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6
Codeset to Send National IEs: 6
Max Message Size to Send: 260
Supplementary Service Protocol: a
Digit Handling (in/out): enbloc/enbloc
Trunk Hunt: cyclical
Digital Loss Group: 13
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200
Synchronization: async
Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0
TRUNK FEATURES
ACA Assignment? n
Measured: none
Wideband Support? n
Internal Alert? n
Maintenance Tests? y
Data Restriction? n
NCA-TSC Trunk Member:
Send Name: n
Send Calling Number: n
Used for DCS? n
Suppress # Outpulsing? n
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider
Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number:
Send UUI IE? y
Send UCID? n
Send Codeset 6/7 LAI IE? y
Ds1 Echo Cancellation? n
US NI Delayed Calling Name Update? n
SBS? n Network (Japan) Needs Connect Before Disconnect?
...so, from this info can anyone tell me what I am doing wrong?
Thanks.
Here is how I have it set up.
Bit Rate: 1.544
Line Coding: b8zs
Line Compensation: 1
Framing Mode: esf
Signaling Mode: isdn-pri
Connect: network
TN-C7 Long Timers? n
Country Protocol: 1
Interworking Message: PROGress
Protocol Version: a
Interface Companding: mulaw
CRC? n
Idle Code: 11111111
DCP/Analog Bearer Capability: 3.1kHz
Slip Detection? n
Near-end CSU Type: integrated
Echo Cancellation? n
ESF DATA LINK OPTIONS
Network Management Protocol: tabs
Send ANSI-T1.403 One-Second Performance Reports? n
Far-end CSU Address: b
INTEGRATED CSU OPTIONS
Transmit LBO: 0db
Receive ALBO: 26db
Upon DTE LOS: loopback
CPE LOOPBACK JACK OPTIONS
Supply CPE Loopback Jack Power? n
The Trunk Group set up is like this:
Group Type: isdn
CDR Reports: n
Group Name: 401 CTI DEV ISDN
COR: 1
TN: 1
TAC: 234
Direction: two-way
Outgoing Display? n
Carrier Medium: PRI/BRI
Dial Access? n
Busy Threshold: 255
Night Service:
Queue Length: 0
Service Type: tie
Auth Code? n
TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6
Codeset to Send National IEs: 6
Max Message Size to Send: 260
Supplementary Service Protocol: a
Digit Handling (in/out): enbloc/enbloc
Trunk Hunt: cyclical
Digital Loss Group: 13
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200
Synchronization: async
Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0
TRUNK FEATURES
ACA Assignment? n
Measured: none
Wideband Support? n
Internal Alert? n
Maintenance Tests? y
Data Restriction? n
NCA-TSC Trunk Member:
Send Name: n
Send Calling Number: n
Used for DCS? n
Suppress # Outpulsing? n
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider
Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number:
Send UUI IE? y
Send UCID? n
Send Codeset 6/7 LAI IE? y
Ds1 Echo Cancellation? n
US NI Delayed Calling Name Update? n
SBS? n Network (Japan) Needs Connect Before Disconnect?
...so, from this info can anyone tell me what I am doing wrong?
Thanks.