Trying to program a new PVR - missing something 3

[dawg2]

I have an opt 61c that I am trying to add ARD to PVR. I already have some of these circuits built but my vendor is not longer available. IPC came out and added another T1 block for ARD's. In MOPE I have cross connected from T1 position 1 to feed pair 131. At switch side I cross connected 4 0 2 0 to feed pair 131.
In programming I created:

TN 004 0 02 00
TYPE COT
CDEN 8D
CUST 0
XTRK XUT
IMP 600
BIMP 3COM
NCOS 4
RTMB 31 26
PRDN 4425
CMF NO
SIGL LOP
SUPN NO
CLS UNR DTN WTA LPR APN THFD
P10 NTC LOL
TKID
DATE 10 APR 2012
Route 31 I did not change anything at this, because it was already built. Do I need to add anything?
YPE: rdb
CUST 0
ROUT 31

TYPE RDB
CUST 00
ROUT 31
DES TRADERS
TKTP COT
PRIV YES
SAT NO
RCLS EXT
DTRK NO
ISDN NO
PTYP ACO
AUTO NO
ICOG IAO
RANX NO
TRMB YES
STEP
CPP NO
TARG 01
BILN NO
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512
IENB 5
TFD 0
LEXT 100
SST 3 0
NEDC ETH
FEDC ORG
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DRNG NO
CDR NO
MUS NO
MANO NO
EQAR NO
OHQ NO
OHQT 00
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

At switch level I programmed key 13 pvr 4425.

what am I missing? When I touch key 13 the arrow show but no ringing sounds or connection.

I did install a new truck card at 4 0 2 ... I did not do anything for that programming except program the 4 0 2 0
I need to get this active any help and assistants would be greatly appreciated.
Thank you

 

[KCFLHRC]

Make sure you have dial tone at the block with a butt set on tn 4 0 2 0

 

[dawg2]

I do not have dial tone or any noise at 4 0 2 0. Do I need to enable the new truck card? If so, how? Please help!
Thank you

 

[jaxuser]

Are you certain that the trunk that Telco provided is loop start and not ground start?

 

[dawg2]

It is a T1 digital handoff to 66 blocks from IPC. Here is a copy of an a working, but I inserted a new card at 4 0 2

TN 024 0 01 00
TYPE COT
CDEN 8D
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
NCOS 0
RTMB 31 7
PRDN 4406
CMF NO
SIGL LOP
SUPN NO
CLS UNR DTN WTA LPR APN THFD
P10 NTC LOL
TKID
DATE 17 MAY 2010

 

[jaxuser]

ok, if this one is working, can you draw dial tone on it from the block? If not, try via mtce set.

 

[KCFLHRC]

If you don't have dial tone at the block that is your problem

 

[dawg2]

When I check to go truck Iget the ring down (like what suppose to happen)
How many truck can you do per card?
I would like to get this working,

 

[KCFLHRC]

8 trunks per card on a NT8D14 univ. trunk card. Your TN 4 0 2 0 should be on the white/blue of the 25 pair cable.

 

[KCFLHRC]

Card slot 4 0 2 should be the C cable on the I/O panel. Make sure the amphenol is plugged in good. Do you have other things working in loop 4 0?

 

[GHTROUT]

As you know, there won't be dial tone - there should be immediate ring when you go off hook - and hopefully the otrher end is there to answer. If you get that at the wires from the channel bank (or whomever gave you the T1 full of ARDs) then you proved the line is good to the trading partner.

Put your toner on the trunk TN and see if you hear it on the phone when you press the key. If you don't, OUT the trunk and rebuild it on the next TN. If that does not woek, I like all the other posts better than mine.

You are right about Route 31 - you do not need to change it. If you do, all the other ARDs may stop working.


--
Nortel Resources at GHTROUT.com World Famous!
--

 

[dawg2]

Thank you for all your assistants. I have it working now. Thank you for the advice with toner..... I check had good connection from switch, able to trace cable issue at T1 cross.

Thank you to all for your help and advice!

 

[nessman]

Just keep in mind that NT8D14 trunk cards are wired at the 66 blocks differently than your analog or digital line cards... so as you add more trunks - just be sure you're punching down in the right place. Not gonna give away the answers... RTFM, er... pull up the documentation.

Also, in LD 20, do a STAT 4 0 2 and see what comes back. If everything's disabled, you'll get nothing on the PVR key - so in that case, in LD 20 do an ENLC 4 0 2 to enable the card and an ENLU 4 0 2 0 to enable that TN.

If you're still running into problems, then you either have a bad port, or a bad card.

 

[dawg2]

Thank you for the response and I do know the cross connect secret.
This issue was cross connect at T1 terminal.

Thank you all for the advice and knowledge.